Skip to content 
1- Blink Camera Flashing Red with New Batteries
Your Blink camera’s blinking red light can be very confusing, particularly if you recently inserted new batteries.
It throws off your home security system and leaves you perplexed as to why.
But fear not—there are multiple simple answers to this seemingly difficult issue.
With new batteries, this thorough guide will explore the causes of a blinking red Blink camera and provide you with a step-by-step solution.
2- Understanding the Blink Camera’s Red Light
Let’s first examine the meaning of your Blink camera’s blinking red light before moving on to possible fixes.
Usually, there are three primary offenders:
I. Low Battery (Deceptive New Batteries):
Although new batteries can last up to two years, a number of circumstances can cause them to drain more quickly.
Insufficient power may result from frequent recordings made in high-activity regions, or even from using non-brand-new batteries that fall under the “fresh” category.
If your blink camera is flashing red 6 times, you can visit this article for its simple solution Blink Camera Flashing Red 6 Times – Causes & Solution – (smartvisliving.com)
II. Wi-Fi Woes:
For blink cameras to work perfectly, there needs to be a strong and consistent Wi-Fi signal.
This annoying blinking red light may appear if your camera is situated far from your router or if the Wi-Fi signal is weak overall.
III. Other Potential Causes
Although less often, the problem can be caused by an old firmware that needs to be updated or a malfunctioning sync module.
3- Troubleshooting Steps:
After learning about the possible reasons, let’s look at several fixes to get your Blink camera back to recording.
This is an explanation of the troubleshooting procedures, arranged logically:
I. Double-Down on Battery Verification:
- Examine Battery Type and Placement: Verify that you are using the appropriate battery type, which Blink recommends (AA lithium batteries are usually the best option).
Verify again that the batteries are inserted with the positive and negative ends positioned in accordance with the indications on the battery compartment of the camera. - It’s Best Fresh: Even while brand-new batteries might seem sufficient, choose a different brand—ideally one you recently bought from a reputable source.
Rechargeable batteries should not be used since your Blink camera may not receive the steady power it needs.
II. Wi-Fi Signal Strength Matters
- Check Your Internet Connection: The first thing you should do is make sure your internet connection is steady and operating as it should.
To verify internet access, consider using a different device to browse the web or doing an internet speed test. - Bridge the Gap: The Wi-Fi connection may be weak if your Blink camera is situated distant from your router.
For a stronger connection, think about moving the camera closer to the router.
If moving isn’t an option, consider using Wi-Fi extenders to strengthen the signal in that particular area. - Router Reboot: Rebooting the router might occasionally fix connectivity problems.
Restarting your router after a brief period of inactivity is known as a power cycle.
Prior to verifying the condition of your Blink camera, let it finish rebooting.
III. Restarting the Blink Camera:
- Battery Power Cycle: This is a straightforward yet efficient method of troubleshooting.
After taking out the batteries for a little while, firmly replace them in your Blink camera.
This soft reboot may occasionally fix little bugs that are the source of the blinking red light. - Use the app to power cycle: For details on power cycling the particular camera model you own, consult the Blink app.
This can entail opening the app’s camera settings and sending a command to turn the camera on and off.
IV. Firmware Updates:
Check the Blink app for updates: Launch the Blink app, then find the camera-specific options section.
If there are any firmware upgrades available, the app will let you know.
You can make sure your camera has the most recent performance enhancements and bug fixes by installing the most recent firmware.
V. Resetting the Camera:
Check the Blink app or website: You may need to reset your Blink camera to factory settings if none of the previously suggested fixes work.
For exact instructions on how to conduct a factory reset on your camera model, use the Blink app or the Blink website.
Be careful: Resetting the camera will remove all of your recordings and settings. This step should only be taken in case all other troubleshooting techniques fail.
4- Advanced Troubleshooting:
Here are some other things to think about if, despite carefully following the instructions above, your Blink camera is still showing the blinking red light:
I. Sync Module Issues:
Should your Blink camera system make use of a sync module, you may need to troubleshoot it. Try this out:
a. Power Cycle the Sync Module:
Take the sync module out of the power outlet for a brief period of time, then put it back in.
When it has finished rebooting, see if the red light on the camera goes out.
b. Move the Sync Module:
Communication may be impeded if the sync module is placed too far from your Blink camera.
To guarantee a stronger connection, think about moving it to a more central area of your house.
II. Examining for Physical Damage:
Although it is less frequent, there is a remote chance that the malfunction is being caused by physical damage to your Blink camera.
Examine the camera for any evident water damage, cracks, or corrosion on the battery terminals.
For additional help, get in touch with Blink support if you believe there has been physical damage.
5- Optimizing Blink Camera Performance:
The following advice will help you get the most out of your Blink camera’s battery and reduce the likelihood that you’ll see the dreaded blinking red light that indicates a low battery:
I. Modify the Motion Detection Settings:
Recording often will quickly deplete your battery. Adjust the Blink app’s motion detection settings to cut down on pointless recordings.
Think about adjusting zones in the camera’s field of view to concentrate on particular regions where you wish to get action shots.
II. Lower the Recording Resolution:
High-resolution recordings provide a higher level of clarity, but they draw more power from the battery.
If your demands don’t require crystal-clear footage, you might want to try lowering the app’s recording resolution.
III. Night Vision Optimization:
To capture sharp photographs in low light, the night vision mode makes use of more power.
Disabling night vision within the app will help you save battery life if it’s not a crucial function for your camera’s position.
6- Contact Blink Support
It’s time to contact Blink support if you’ve tried every troubleshooting solution in this article and your Blink camera is still showing the blinking red light.
How to contact them is as follows:
- Blink Support page: Go to Blink Support (blinkforhome.com) to see the Blink help page.They have a thorough knowledge base with FAQs and articles for troubleshooting that can help with your particular problem.
- Blink Support Contact Information: There are ways to get in touch with the Blink support staff directly through their website.
Depending on your preference, you have the option of live chat, email assistance, or a phone call.
7- Conclusion
New batteries may cause your Blink camera to blink red, which might be confusing but doesn’t always mean you should be concerned.
You’ll be well-equipped to identify the problem and restore your Blink camera’s ability to record by methodically following the troubleshooting methods in this guide.
As always, it’s important to recognize the possible reasons, carefully adhere to the fixes, and don’t hesitate to contact Blink support when necessary.
You can get your home security system operating normally again with a little work.
